Skip to content

PSP Go Battery Replacement - Complete Guide

Overview

PSP Go's built-in lithium battery capacity decreases over time, reducing runtime. This guide details safe PSP Go battery replacement to restore device battery life.

Required Tools

  • Phillips screwdriver (PH00)
  • Plastic spudger
  • Tweezers
  • New PSP Go specific battery (model: PSP-S110)
  • Anti-static wrist strap (recommended)

Safety Warnings

⚠️ Battery Safety Critical ⚠️

  1. No piercing: Never puncture or damage lithium batteries
  2. Avoid shorts: Don't let battery contacts touch metal objects
  3. Heat avoidance: Don't operate in high temperature environments
  4. Professional disposal: Damaged batteries require professional recycling
  5. Use genuine: Only use OEM or certified safe batteries

Battery Specifications

  • Model: PSP-S110
  • Type: Lithium-ion polymer
  • Voltage: 3.7V
  • Capacity: 930mAh
  • Dimensions: ~53×33×5mm

Detailed Steps

Step 1: Safety Preparation

  1. Completely power off PSP Go
  2. Disconnect all external devices
  3. Place insulating mat on work surface
  4. Wear anti-static wrist strap (if available)

Step 2: Remove Back Cover

  1. Place PSP Go face down
  2. Remove 4 crosshead screws from back cover
  3. Use plastic spudger to pry open cover from bottom
  4. Carefully remove back cover, avoid damaging clips

Step 3: Disconnect Old Battery

  1. Locate battery connector (right side of motherboard)
  2. Gently lift battery connector with plastic tool
  3. Carefully remove battery ribbon cable
  4. Important: Ensure battery completely disconnected

Step 4: Remove Old Battery

  1. Battery secured with adhesive to chassis
  2. Gently lift battery corner with plastic spudger
  3. Slowly separate battery from adhesive
  4. If adhesive stubborn, use minimal isopropyl alcohol
  5. Completely remove old battery

Step 5: Clean Battery Compartment

  1. Clean residual adhesive with cotton swabs
  2. Wipe contact areas with isopropyl alcohol
  3. Ensure compartment completely dry
  4. Check battery contacts cleanliness

Step 6: Install New Battery

  1. Apply new adhesive to new battery back
  2. Align battery ribbon with connector
  3. Gently insert ribbon, ensure fully seated
  4. Place battery in compartment, press to secure
  5. Ensure battery flat, no bulging

Step 7: Reassemble

  1. Replace back cover, align all clips
  2. Press gently, ensure all clips engaged
  3. Replace 4 screws
  4. Don't overtighten screws

Initial Use & Calibration

Initial Charging

  1. Use OEM charger
  2. First charge: recommend 4 hours full charge
  3. Don't use device while charging

Battery Calibration

  1. After full charge, use until auto-shutdown
  2. Recharge fully (without interruption)
  3. Repeat 2-3 times for optimal battery performance

Performance Testing

Runtime Testing

  1. Video playback at medium brightness: ~3-4 hours
  2. Gaming time: ~3-5 hours (game dependent)
  3. Standby time: ~10-15 days

Charging Testing

  1. Full charge time: ~2-3 hours
  2. Device temperature while charging: slightly warm normal
  3. Charge indicator: orange charging, green fully charged

Troubleshooting Common Issues

Issue 1: Won't Power On

  • Possible cause: Battery not connected or no charge
  • Solution: Check battery connection, charge 30 minutes then retry

Issue 2: Charge Light Not On

  • Possible cause: Charger failure or battery connection issue
  • Solution: Try different charger, check battery connection

Issue 3: Swollen Battery

  • Stop using immediately: Swollen batteries risk explosion
  • Safe handling: Place battery in fireproof bag, contact professional recycling
  • Don't attempt repair: Swollen batteries must be replaced

Issue 4: Short Runtime

  • Possible cause: Battery aging or system settings
  • Solution: Perform battery calibration, adjust screen brightness etc.

Battery Maintenance Guide

Daily Use

  1. Avoid deep discharge: Charge above 20% when possible
  2. Avoid overcharging: Unplug after full charge
  3. Temperature range: Use and charge at 0-35°C (32-95°F)

Long-Term Storage

  1. Charge state: Store at ~50% charge
  2. Storage environment: Cool, dry place, avoid heat
  3. Regular checks: Check charge every 3 months

Performance Optimization

  1. Screen brightness: Lower brightness significantly extends runtime
  2. Wireless functions: Turn off unused Wi-Fi and Bluetooth
  3. Background apps: Close unnecessary background applications

Genuine vs Counterfeit Battery Identification

Genuine Battery Characteristics

  • Clear SONY logo and model number
  • Clean solder joints
  • Accurate weight (~20g)
  • Proper packaging and anti-counterfeit labels

Counterfeit Battery Risks

  • Inflated capacity claims
  • Missing safety protections
  • Short lifespan
  • Safety hazards

Professional Repair Advice

When Replacement Needed

  1. Significantly reduced runtime (<2 hours)
  2. Quick discharge after charging
  3. Battery swelling or deformation
  4. Device auto-shutdown

Repair Considerations

  1. Purchase source: Buy from authorized dealers
  2. Post-installation check: Comprehensive testing after installation
  3. Old battery disposal: Take to e-waste recycling point
  4. Warranty preservation: Keep purchase receipt and warranty card

Summary

PSP Go battery replacement is moderately difficult, but battery safety requires special attention. Following this guide, most users can safely complete replacement. New battery revitalizes your PSP Go for extended gaming sessions.

Repair difficulty: ★★☆☆☆ (moderate)
Time required: 20-40 minutes
Safety level: Requires special safety attention

Important reminder: If unfamiliar with lithium battery handling or concerned about safety, seek professional help. Safety always comes first!